Roof replacement
Roof replacement
Read more
Roofing in Frederick & Central MD
Roof and gutters together
Replacing both at once, by the people doing both. The junction where a roof edge meets a gutter is the detail two separate contractors each assume the other handled, and it is where a great deal of fascia rot begins.
Licensed & insuredFree written estimatesFrederick-based crewClean-site guarantee
Quick answer
Should I replace gutters at the same time as the roof?
If the gutters have less than about five years left in them, yes. The money argument is real — you save $700 to $1,400 in duplicated set-up and clean-up — but the technical argument is stronger. The drip edge and the gutter have to be fitted as one detail, and when two trades do them months apart neither owns that junction. If your gutters are newer and sound, we will say so and protect them rather than sell you new ones.
The work
What roof and gutters actually involves.
If your gutters are near the end and the roof is going anyway, doing them together is the obvious move — and not only to save a mobilisation. The eave is a single detail made of three parts: the drip edge at the roof edge, the fascia board behind it, and the gutter hung off that fascia. Each part only works if the one next to it was fitted with it in mind.
The failure is specific and extremely common. New drip edge gets fitted to the existing gutters and ends up sitting behind or inside the back of the gutter, so water running off the roof slips behind the gutter and down the fascia instead of into the trough. Or new gutters go onto an old drip edge that is too short to reach them. Either way the symptom is a stained, soft fascia under gutters that nobody can see anything wrong with.
Doing both at once also means the fascia is accessible exactly once. With the gutters down and the roof edge open, replacing a rotten board is twenty minutes of work; six months later, with new gutters hung on it, the same board means taking the gutters back down.
One visit, one crew
Drip edge over the gutter
Fascia repaired while open
What roof and gutters costs in Maryland
Figures for both trades on a typical single-family house, done as one job. Doing them together removes roughly a thousand dollars of duplicated set-up and clean-up.
- Roof and gutters, typical single-family
- $13,500 – $26,000
- Gutters and downspouts alone, 5-inch K-style
- $8 – $14 per linear foot
- 6-inch oversized gutter upgrade
- $11 – $18 per linear foot
- Drip edge, new, full perimeter
- $450 – $1,100
- Fascia replacement, per linear foot
- $12 – $26
- Saving versus two separate visits
- $700 – $1,400
Ranges, not quotes. Real numbers come from a walkthrough — access, condition, height and finish level move a price more than square footage does. Estimates are free and in writing.
Get your numberFull roof and gutters cost guide for MarylandPrefer to just talk?
Call and describe the job. You’ll get a straight answer on whether it’s something we do and roughly what it runs.
(301) 524-1729
Self-performed
Roof and gutters together
What’s included
Everything the roof and gutters scope actually covers.
Written into the estimate, not assumed. If something on your job is not on this list, it gets priced and named before anyone starts.
Drip edge over the back of the gutter
01Fitted so runoff lands in the trough rather than behind it. This single detail is the reason to do the two jobs together rather than six months apart.
Fascia and sub-fascia repaired while open
02With the gutters off and the edge exposed, soft boards get replaced at the one moment it is cheap to do. We price it per foot rather than as a surprise.
Apron and valley terminations detailed
03Where a valley or a lower roof discharges into a gutter, the metal is shaped to deliver the water into it instead of over the front. Volume at that point is the reason many gutters appear undersized.
Downspouts and discharge reviewed
04Sizing, placement and where the water actually goes once it leaves the house, since a perfect gutter that dumps against the foundation has only moved the problem.
One mobilisation, one schedule
05One set-up, one dumpster, one clean-up, and no gap where the roof is new and the gutters are off. It is also meaningfully cheaper than two separate visits.
Ice-and-water at the eaves
06Membrane at the eave as part of the roof, which is where Maryland's freeze-and-thaw backs water up under the shingles when a gutter ices.
On the job
Roofing work across Frederick & Central MD.
What the trade looks like at each stage. Photos of our own recent jobs come out at the walkthrough, on the actual house.
Straight answers
Roof and gutters questions
Not covered here? Call and ask — you’ll get a real answer, not a “depends on the job”.
Roof first, gutters immediately after, within the same job. The gutters come down, the roof is torn off and rebuilt with new drip edge sized to reach the trough, the fascia gets repaired while it is exposed, and then the new gutters hang on sound wood and tuck under that drip edge. Hanging gutters before the roofing crew arrives means they get dented, filled with debris, or taken down again.
A typical single-family house runs $13,500 to $26,000 in 2026 for both, with the roof the large majority of it. Gutters and downspouts on their own are $8 to $14 per linear foot in 5-inch K-style, or $11 to $18 for 6-inch, which is worth considering on a long roof slope or where a valley discharges into one run. We quote both lines separately so you can see what each is.
No, and this is worth being clear about because it gets sold that way. An ice dam is caused by heat escaping into the attic, melting snow on a warm deck, and that water refreezing at the cold eave. The gutter is where the ice ends up, not where the problem starts. New gutters and new ice-and-water membrane limit the damage when it happens; fixing the cause is air sealing and the ventilation work, which is why we look at the attic during a re-roof rather than only at the roof.
Same crew, same visit
The rest of the roofing work.
Most roofing jobs are two or three of these at once, which is why they are priced and scheduled together rather than as separate call-outs.
From the field
Read up before you book.
Longer answers than a quote page has room for — how the work fails, what putting it right actually involves, and when waiting is the honest call.
Sources worth your time
Check us, and check the work
None of these are ours. They are the offices and standards bodies that set the rules we work to, so you can verify what we say rather than take it.
SMACNA architectural sheet metal standards
The trade standard for gutter and downspout sizing, expansion joints and hanger spacing.
OpenNational Roofing Contractors Association
Independent guidance on roof edge detailing, where a roof stops and a gutter starts.
OpenAsphalt Roofing Manufacturers Association
The trade body for the people who actually make asphalt shingles. Its technical bulletins cover ventilation ratios, fastener patterns and what voids a shingle warranty — which is usually a layover or a starved attic rather than anything the weather did.
Open
Talk to the people doing the work
Get a straight number for the whole job.
Tell us what needs doing. We’ll walk it with you, sequence every trade it touches, put the price in writing, and leave you to decide.
Get a quote
Let’s price your project.
Two short steps. No obligation, no pressure — just a clear number and a straight answer about what the job involves.
Tick as many as you like. Most jobs are two or three of them at once, and I sort out the detail when I come and look. Nobody gets turned away for choosing the wrong box.
